收藏本站
Installation
2.8
SOFTWARE SETUP
1. Launch MPLAB IDE v6.xx.
2. From the Configure menu, select Select Device. In this dialog, choose the device
you will be emulating and click OK .
3. From the Debugger menu, select Select Tool and then MPLAB ICE 4000 to
enable the emulator.
Note:
If you cannot select the emulator as the debug tool, please see
Appendix A. “Troubleshooting” .
Once you have selected MPLAB ICE 4000, debug options will appear on the
Debugger menu.
Note:
It is recommended that you not have a programmer enabled at the
same time as the emulator. See Appendix A. “Troubleshooting” for
more information.
4. The default port setting is USB = ICEUSB-0. If you wish to change this settings,
you may do so on the Port tab of the Debugger>Settings dialog. See
Section 3.4 “Configuring the Communications Port” for more information.
5. MPLAB ICE 4000 allows the emulator processor module to be powered by either
the emulator pod or the target system. This is set up in MPLAB IDE as follows:
? Emulator pod: Debugger>Settings , Power tab, “Processor Power From
Emulator”
? Target system: Debugger>Settings , Power tab, “Processor Power From
Target Board”
Note:
You must select “Processor Power From Target Board” when using
low-voltage emulation.
See Section 3.5 “Selecting Processor Power” for more information. Also,
refer to the MPLAB ICE 4000 Processor Module and Device Adapter Specifica-
tion for processor module power requirements before configuring the system for
target system power.
When connecting to a target application system, you may notice a voltage level
on the target application, even though you have not yet applied power to the tar-
get application circuit. This is normal and is due to current leakage of protection
diodes through V CC of the Device Adapter. The current leakage will typically be
less than 20 mA. However, if the target application is using a voltage regulator, it
should be noted that some regulators require the use of an external shunt diode
between V IN and V OUT for reverse-bias protection. Refer to the manufacture’s
data sheets for additional information.
MPLAB ICE 4000 should now be ready for you to use as an emulator. If you have had
problems, please consult Appendix A. “Troubleshooting” . Otherwise, proceed to the
next chapter for additional software setup considerations.
? 2004 Microchip Technology Inc.
DS51490A-page 13
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
PMF18WE0 PROCESSOR MODULE FOR ICE4000
PMT823004F GP THREE ELEMENTS S.A. 230V T/H
PPM3-MK2 PROGRAMMER PRODUCTION ISP
PPM3A1-UPG5M UPGRADE PPM3 RAC DEVELOPMENT
PQ-MDS-PCIEXP PCI EXPANDER ADAPTOR
PQF-44 PLUG QFP 44PIN (SOLDER DOWN)
PRG18BB471MS1RB THERMISTOR
PS1600 POWER SUPPLY HOTSWAP 90-245V
相关代理商/技术参数
PMF18WE0 功能描述:插座和适配器 Processor MOD RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
PMF18WE0 制造商:Microchip Technology Inc 功能描述:Tools Emulator For Use With:P
PMF18WE1 功能描述:插座和适配器 PIC18F8680 RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
PMF18WF0 功能描述:插座和适配器 Processor Module RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
PMF18WH0 功能描述:插座和适配器 PIC18F ICE4000 RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
PMF18WJ0 功能描述:插座和适配器 Processor MOD RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
PMF18WJ1 功能描述:插座和适配器 Processor Module RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
PMF18WK0 功能描述:插座和适配器 PIC18F RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x